Dr Dabber Boost Evo Electric Dab Rig ERig - White

How Do I Turn My Dr Dabber Boost Evo On and Off?

Press the power button five times (5) fast to turn the device on or off.

How Do I Change The Temperature Setting On My Dr Dabber Boost Evo?

Press the power button three times (3) to change the temperature setting. The temperature setting can be adjusted while the device is heating up to temperature. It is recommended to utilize the lower temperature settings when using the Dr Dabber Boost Evo, to maximize flavor, and the higher temperature setting are recommended to maximize vapor production.

• Temp 1 – 500 Degrees – Pink
• Temp 2 – 550 Degrees – Purple
• Temp 3 – 600 Degrees – Blue
• Temp 4 – 650 Degrees – Green
• Temp 5 – 700 Degrees – Orange
• Temp 6 – 750 Degrees – White

How Do I Use My Dr Dabber Boost Evo?

• After powering the unit on and adjusting the temperature setting to your preferred temperature, remove the glass attachment from the unit and add water. The attachment should be filled with water from the top and the water level should be a couple of millimeters above the percolator holes in the glass attachment.
• Attach the water bubbler attachment to the quick connect adapter.
• Load the atomizer with your preferred materials.
• Place the quick connect adapter with the glass attachment attached back onto the Dr Dabber Boost Base.
• Press and hold the power button for thee seconds (3) to initiate heat up.
• Press and hold the airflow release button when ready to clear the glass attachment.

What is “Party Mode” on the Dr Dabber Boost Evo?

Party Mode is something we usually call “session mode”, after initiating heat up the Dr Dabber Boost Evo will hold the atomizer temperature for a certain number of seconds. You can adjust the party mode settings by completing the following steps:

• Power the unit off.
• While the unit is turned off, press and hold the power button to change the session mode time.
• The LED light will blink two times (2) to indicate a hold time of 20 seconds, or four times (4) to indicate a hold time of 40 seconds.

What is “Glow Mode” on the Dr Dabber Boost Evo?

Glow Mode is the when the LED lights are illuminated in a decorative pattern.

• To turn Glow Mode off or on, press the power button four times (4).
• Press the power button two times (2) to cycle between the five LED light presets on the Dr Dabber Boost.

What is “Stealth Mode” on the Dr Dabber Boost Evo?

Stealth Mode is when the LED lights on the Dr Dabber Boost Evo are dimmed.

• Press the power button two times (2) whole Glow Mode is off to turn Stealth Mode on or off.

Charging the Dr Dabber Boost Evo

The charger LED lights will indicate the batteries status, the charging LED’s will pulse white while the device and charging, then turn solid white when the device is fully charged.

When the Dr Dabber Boost Evo blinks its temperature setting color three times (3), this indicates low battery. Please charge the device with its included charger until the LED lights are a solid white, before use.

How Do I Clean My Dr Dabber Boost Evo?

• Remove the quick connect adapter and the glass attachment from the base.
• Remove the glass attachment from the adapter and clean the adapter with a cotton swab dipped in isopropyl alcohol. Be sure to avoid the colored portion of the adapter and clean only the metal ring at the bottom and the threading.
• You can also remove the silicone ring out of the top of the adapter and run it under hot water to remove any excess residue, use a cotton swab for more stubborn residue.
• Pour out the water from the glass attachment and pour in some warm water, you can give the glass attachment a good shake after the warm water is placed inside to loosen up residue.
• For more stubborn residue, you can pour in some isopropyl alcohol and salt into the glass attachment, give it a shake, followed by a rinse with warm water. Allow the glass attachment to fully dry before reassembling.
• Remove the atomizer from the base, the atomizer is connected to the base by a magnetic connection. Simply pull the atomize up to remove.
• With a cotton swab soaked in isopropyl alcohol, clean the inside of the atomizer. You can use a cotton swab soaked in hot water to remove any access residue. Let dry before assembling.

You should clean out the inside portion of the atomizer with a cotton swab and iso alcohol after each session to avoid a large amount of build up.

How Do I Recalibrate My Dr Dabber Boost Evo for My New Atomizer?

When purchasing a new atomizer, your unit must be recalibrated with the new atomizer to get the most accurate temperature readings.

• Turn the Dr Dabber Boost Evo off and be sure not to charge it within 15 minutes prior to recalibrating.
• While the unit is off, press the power button four times (4) and hold the power button on the fourth press to recalibrate the unit.
• A successful recalibration is indicated by the LED lights blinking white, if the lights are blinking red that means the calibration was unsuccessful.

If you are experiencing any issues with this device or have any additional questions, please send an email to info@e-nail.com, stating the specific problem. Please include a picture or video showing the fault and also include your order number.