Lookah Unicorn Mini FAQ
Lookah Unicorn Mini Flashing Red Light
The red flashing light indicates low power / low battery.
Please try the following steps:
- 1. Please charge the device for about 2 hours, the LED indicator light sholuld illuminate red when charging.
- 2. Press the power button 5 times to turn the device off while charging.
- 3. After charging, click the button 5 times fast to turn on the device.
Lookah Unicorn Mini Flashing Puple Light
The purple flashing light indicates high-temperature protection. Please allow the device to cool down before attempting to use it again.
Lookah Unicorn Mini Flashing Yellow Light - 5 Times
If the indicator light flashes yellow 5 times when you press the power button then this may signal an open circuit problem. Sometimes this can happen if the coil / atomizer isn't screwed on correctly or if it is screwed on too tight.
Please try the following steps:
- 1. Unscrew and take off the coil, use a cotton swab and some alcohol cleaner to clean any oil or residue on the 710 thread end of the coil and the 710 thread hole of the unicorn mini.
- 2. Replace the coil by screwing it back into the threaded hole.
- 3. Turn on the device and test it to see if this resolves the issue.
- 4. If the indicator light still flashes yellow, please try another new coil.
Lookah Unicorn Mini Flashing Yellow Light - 8 Times
If the indicator light flashes yellow 8 times when you press the power button then this may signal an open circuit problem.
Please try the following steps:
- 1. Unscrew and take off the coil, use a cotton swab and some alcohol cleaner to clean any oil or waxy residue on the 710 thread end of the coil and the 710 thread hole of the unicorn mini.
- 2. Replace the coil by screwing it back into the threaded hole.
- 3. Turn on the device and test it to see if this resolves the issue.
- 4. If the indicator light still flashes yellow, please try another new coil.
Where Can I Get Replacement Unicorn Mini Accessories?
You can purchase accessories for the Unicorn Mini by clicking here: www.e-nail.com. We have all four types of replacement coils.
Like the newer devices we've seen released by Lookah, the Unicorn Mini uses a 710 thread coils. There are currently 4 different types of atomizer/coil options to choose from labeled as Type A, Type B, Type C, and Type D. All are made of crushed quartz, heres a brief explanation of each:
- Type A Coil: Quartz Dish Coil - Features a large round surface area for bigger dabs or for more evenly heated smaller dabs, and 360 air flow for large more thin clouds.
- Type B Coil: Dual Hole Coil - Features two small holes at the bottom to expose more heat for higher temperature dabs and quick heating times, resulting in milkier white clouds.
- Type C Coil: Square Quartz Coil - Features an airflow hole across the side for steady airflow and a smaller square surface area to get the most out of your concentrates, this atomizer is considered to be "wax saving".
- Type D Coil: See Through Quartz Coil - Features clear quartz walls with a crushed quartz bottom, with two small holes similar to the Type B coil. Clear quartz is wasier to clean and lasts much longer than crushed quartz. I believe this is lookahs version of a 3D atomizer.
I Am Having A Problem With My Unicorn Mini Coil
The coil is a consumable good and will wear out over time, depending on how often it is used.
- To ensure the coil last as long as possible, make sure you fully burn all the concentrates off the coil after each dab.
- If you leave concentrates on the coil or inside the airways it will harden and possibly ruin or wear out the coil prematurely.
- Please do not insert the cleaning brush into the airways of the coil as this can damage it.
- If your coil is worn out, please replace it with a new one.
How Do I Remove The Unicorn Mini Glass?
Removal Steps:
- 1. Remove the glass top, similar to when you are loading the device.
- 2. Unscrew the magnetic botton base from the glass top.
If your device is still not working correctly, please send an email to info@e-nail.com, stating the specific problem. Please include a picture or video showing the fault and also include your order number.