VLAB Halo Smart ERig Electric Dab Rig: Peach Pink

How to Use VLAB Halo Electric Dab Rig

• 1. Fully charge the device before first use, when the power button is illuminated red the battery is charged under 30%, the light will then illuminate white after it is charged over 60%, once charging is completed the Halo will vibrate and the light will turn off. The Halo base should be fully charged in one hour.
• 2. Fill the glass bubbler with water just above the holes in the percolator, do not fill the glass attachment while it is attached to the VLAB Halo base.
• 3. Align the inlet hole on the front of the glass attachment with the hole on the base leading to the atomizer. Carefully place the glass attachment into the base.
• 4. Power on the device by clicking the power button five times fast. Once the Halo is turned on the power button will flash three times.
• 5. Click the power button three times to toggle through the heat settings:
• Green Light – 480 Degrees
• Blue Light – 600Degrees
• Red Light – 750 Degrees
• —The V1 has three temperature settings and the V2 has 4 temperature settings, the temperature settings may vary based on which version of the Halo you purchased.
• 6. Use loading tool to place concentrates on the bottom surface of the quartz bucket located inside the atomizer. Make sure the concentrates are placed at the bottom of the quartz bucket and not the walls.
• 7. Place carb cap on top of the atomizer.
• 8. Hold the power button down for two seconds to initiate heat up, the device will then vibrate and the led band light around the base will flash the color of the selected temperature setting.
• 9. Once the Halo is heated to selected temperature, it will continue to maintain heat for 30 seconds.
• 10. After the heating cycle is finished the device will vibrate and the lights will turn off.
• 11. Use a cotton swab to clean the quartz bucket after each use.

How Do I Power Off My VLAB Halo Electric Dab Rig?

• Click the power button twice to turn the device off, after a heating cycle the Halo will go into standby mode. This device will power off automatically after two minutes of inactivity to preserve battery life.

Why is My Halo Electric Dab Rig Blinking Three Times?

This indicates that there is a connection issue, please try the following steps:

• Please unscrew the atomizer and make sure it is screwed in correctly, sometimes the atomizer will not make a clear connection with the firing pin on the base if the threading is off when the atomizer is screwed in.
• If the Halo continues to blink three times, this may be due to a firing pin issue. There is a firing pin on the base and there is also a firing pin at the bottom of the atomizer.
• There is a firing pin on the base and there is also a firing pin at the bottom of the atomizer.
• Unscrew the atomizer, using a dab tool gently lift the firing pin slightly.
• DO NOT lift the firing pin all the way out, this will cause the wiring to disconnect, and the atomizer will stop working completely.
• Very slight lifting of the firing pin will help the atomizer to make a connection with the base and your Halo should start working properly again from there.
• If neither of the above steps resolve the issue, we suggest replacing the atomizer.

Why is My Halo Electric Dab Rig Blinking Five Times?

This indicates that there is a short circuit, or low battery.

• If the Halo base has come into contact with water, allow for the base to dry out completely and then try turning the device on again.
• If the device is dead, please place the device on the charger and allow the Halo to fully charge before attempting to use it again.

Why isn’t My Halo Electric Dab Rig Charging?

• If you place the Halo base on the charger and the light does not illuminate, this may mean the device is already fully charged.
• If the device is not fully charged and the power button light is still not illuminating when placed on the charger, please try a different charging chord, charging block, or a different outlet.
• You should always charge your devices through a direct outlet and not a power strip.

How Do I Clean the Halo Glass Attachment?

• Remove the glass attachment from the Halo base.
• Soak the glass attachment for one hour, either in isopropyl alcohol or in a glass cleaner of your choice.
• Rinse with water and let air dry fully before reassembling.

How Do I Clean the Halo Atomizer?

• Unscrew the atomizer from the Halo base by turning it counterclockwise.
• Remove the quartz bucket insert from the atomizer.
• Soak all parts in isopropyl alcohol for one hour.

—If the quartz bucket insert is stuck inside the atomizer do not attempt to pull it out, soak it in isopropyl alcohol to loosen up the built-up residue and then attempt to remove it from the atomizer.

Warning:

• Make sure the atomizer is fully cool to the touch before unscrewing it.
• Be sure the device is powered off before cleaning.
• After cleaning allow for all parts to dry completely before reassembling.
• Do not blow into glass attachment while it is filled with water and is attached to the base.
• Do not overfill the glass attachment with water.
• Wait at least one minute between heating cycles.
• Do not store this device while the glass attachment is filled with water.
• Keep away from high humidity and moisture, it is best to store the Halo E-Rig in a dry dark place when not in use.
• Do not overfill the atomizer, this will cause the atomizer to flood resulting in the need of a new atomizer.

If your device is still not working correctly, please send an email to info@e-nail.com, stating the specific problem. Please include a picture or video showing the fault and also include your order number.