Terp Slurper Enail Kit

A terp slurper enail is just like a regular quartz banger enail, but with a terp slurper banger instead! It consists of a terp slurper enail banger, an enail coil, and a control box.

A terp slurper enail banger has a different design than a regular bucket. It features a long bottom chamber attached to a dish, as well as a small top bucket usually with a beveled top. Instead of placing your dab inside the banger, its actually placed onto the heated bottom dish.

The beveled edge on top creates an airtight seal when using a marble carb cap. Directing airflow from the bottom of the banger instead of through the top. Where the terp slurper dish meets the long chamber, there are a few slanted holes.

As your dab melts onto the dish, it sucks into the long chamber for vaporization. These holes also help to spin your dabbing accessories, like terp pearls or pills around. Your dab spins around the heated middle chamber with the help of airflow and dab inserts for fast, even, and full vaporization.

The terp slurper banger stands out from other enail bangers because its airflow forces air through the dab. Instead of over it, like with a bucket banger. This design provides the most flavorful and effective dabs, which is why terp slurpers have become so popular!

The enail coil provides precise consistent temperature and heat distribution to the bottom dish of the terp slurper. While there are still challenges in achieving 100% efficiency with terp slurper enails. Also a slight learning curve exists, but mastering it will lead to incredibly flavorful dabs in no time!

Terp slurper enails take longer to heat compared to bucket bangers because of their unique design. These bangers require heating in two areas: the long chamber and the bottom dish. A common mistake is setting the enail to a high temperature setting, like 650°F, to speed up this process. However, this can cause you to burn your dab.

The dabbing temperature for a terp slurper enail should be slightly higher than a regular quartz banger. After the coil reaches the desired temperature, let the banger sit for 2-3 minutes. This is so that there is more heat transfer to the middle chamber without burning the dabs placed on the dish. Remember, for low-temp dabs, aim for 425-475°F; for medium temp, go for 475-525°F; and for high temp, target 525-600°F.

We do not recommend dabbing above 650 degrees since this will cause your dab to burn instead of vaporize. Dabbing at high temperatures can expose you to unwanted health issues.

Step 1. Remove your enail controller with the power cord from the box. Connect the power cord to the controller and plug it into a wall outlet. Do not plug an enail into a power strip.

Step 2. Connect your enail coil to the enail controller.

Step 3. Locate the terp slurper banger included in your kit. The quartz rod at the bottom will slide into the center of your enail coil.

Step 4. Secure the enail banger to your enail coil using an o-clamp.

Step 5. Attach your terp slurper banger to your dab rig.

Step 6. Place your banger accessories onto your terp slurper including your marble carb cap on top.

Once you've set up your enail controller box, power it on. Select your preferred temperature using the up and down arrows. The controller's temperature display will start blinking, indicating the coil is heating. Allow 2-3 minutes after the coil reaches your set temperature before you begin dabbing.

Step 7. Use a dab tool to scoop your desired amount of concentrate and place it onto the bottom dish.

Step 8. Inhale and enjoy!

Both Terp Slurper Enails and Regular Quartz Banger electric nails have their pros and cons. Terp slurper enail bangers produce better flavors but tend to be harder to clean than regular bangers. Regular bucket enail bangers are easier to clean but less offer flavor.

Check out this chart for a head on comparison of both!

Cleaning a Terp Slurper enail banger is the same as any other quartz banger. Use a cotton swab dipped in isopropyl alcohol to clean out any excess reclaim from the bottom after your dab. Some dabbers find it hard to clean the bottom chamber with regular dab swabs. You can purchase specific terp slurper swabs with extra cotton at the tip to fit the chamber perfectly.

For a deep clean, soak your enail banger overnight in a Dunk Tank. Filled with a solution of water, salt, and isopropyl alcohol. The next morning, use a cotton swab to wipe away any leftover residue.

The solution will have loosened most of the buildup, making it easier to clean. Rinse the banger under warm water and wipe it down. If the residue is especially stubborn, heat the banger with your enail before wiping it. Heat the banger to turn the residue into ash, making it easy to rinse away.

The ideal Terp Slurper Enail for you depends on your dabbing size, preferences and style. Various terp slurper electronic nail kits are available, ranging from 25mm for smaller dabs to 35mm for larger dabs.

• For a 25mm Terp Slurper we would suggest going with a 0.05-0.2g dab which is about the size of 1 grain of rice.
• For a 30mm Terp Slurper Quartz Banger, we suggest a 0.1-0.3g dab which is about 1.5 grains of rice.
• For a 35mm Terp Slurper Quartz Banger, we suggest a 0.2-0.4g dab which is about 2 grains of rice.

Each enail dab kit offered at e-nail.com comes with all the necessary components to get you started right away. If you have any questions about which enail kit is best for you, contact our live chat to speak with a dabbing expert!