Dr Dabber Boost Evo Electric Dab Rig ERig - Sugar Sean Edition

Dr Dabber Boost Evo Electric Dab Rig ERig - Sugar Sean Edition

Introducing our very first Limited Edition Boost EVO collab with UFC superstar, Sean O'Malley. Feast your eyes on the Boost EVO: Sugar Sean Edition. This Limited Edition co branded release features a vibrant, tie dye body accompanied by a custom Sugar Sean Edition Packaging and Glass Attachment.

The Dr. Dabber Boost EVO was built from the ground up, incorporating proprietary technology, with one goal in mind: the perfect dab. Attaining the perfect dab every time you use your Electric Dab Rig is something that is usually overlooked. Older electric rigs typically have the standard three temperature control settings, set to heat up until a certain point and then cut off. This was based on wattage and ohm-age to get the desired voltage, not based on actual temperature, which resulted in a large variance in temperature when dabbing your concentrates causing an overall inconsistent dabbing experience.

The Boost EVO has a patent temperature control sensor built in to regulate heating, this means that when you are dialed in, you are DIALED IN. The temperature sensor reads the actual temperature of the atomizer, sending feedback to either continue heating or to stop heating in the event that the atomizer has already reached its preset temperature. Producing a supreme dab. Perfected, even heating with each session.

With six heat settings that have been calibrated with the help of customer feedback from tens of thousands of Boost users, you can rely on your Boost EVO to be consistent every single time.

Pair that technology with a custom quartz dish, interchangeable glass, spectacular RGB ambient lighting and surprisingly long battery life for such a portable device, the Dr. Dabber Boost EVO is truly the next generation of the eRig.

Also Available in Eclipse Black & White

Each Boost EVO: Sugar Sean Edition is hand-dipped, therefore no two units are exactly alike.

Specifications:

• Height: 4" Without Glass - 7.75" With Glass
• Diameter: 2.83"
• Battery: 3400mAh
• Temperature Settings: 6 Setting Ranging from 500 Degrees to 750 Degrees
• USB-C Charging
• Charge Time: 2 Hours
• Quartz Heating Element
• 11 Second Heat Up Time

Features:

• Revolutionary Magnetic Quartz Atomizer with built-in temperature sensor
• Quick Connect Adapter with Airflow release (Carb)
• Straight quartz to glass vapor pathway
• Enhanced Ergonomics with Grip Pads
• Five RGB light modes plus Stealth Mode for discrete dabbing
• Exceptional battery life with built-in protection against over voltage and short circuits
• Up to 60 hits on a single charge
• 20 or 40 Second Sesh Mode
• Pass through Charging
• Auto shutoff after 15 minutes
• Durable and protective carrying case included
• 1 Year Manufacturers Warranty

Includes:

• 1 x Dr. Dabber Boost EVO
• 1 x Boost EVO Quartz Atomizer
• 1 x Boost EVO Replacement Glass Attachment
• 1 x Boost EVO USB-C Charger
• 1 x Boost EVO Quick Connect Adapter
• 1 x Boost EVO Loading Tool

Compatibility:

• Dr Dabber Boost Evo Silicone Dabbing Station
• Dr Dabber Boost Evo Replacement Glass
• Dr Dabber Evo Boost Replacement Atomizer
• Dabbing Accessories

5 Best Electric Dab Rigs of 2021

#3: Dr. Dabber Boost Evo

Dr. Dabber is a big name in the dabbing world, and the Boost Evo is a hugely successful offering from the celebrated brand.

• Offering the electronic rig along with a quartz atomizer, glass attachment, and loading tool, it's got everything you need to get started.
• A single charge can offer up to 60 puffs, with a 20-40 second hold time.
• The design provides perfect airflow for smooth and rich vapor, with a magnetic quartz atomizer that intelligently reads temperature.
• Heats up in 11 seconds, with six temperature presets between 500 and 750 degrees.
• Portable thanks to its size.
• Durable materials to keep it safe.

Click Here to Read about the Top 5 Portable E-Nails of 2021!

How Do I Turn My Dr Dabber Boost Evo On and Off?

Press the power button five times (5) fast to turn the device on or off.

How Do I Change The Temperature Setting On My Dr Dabber Boost Evo?

Press the power button three times (3) to change the temperature setting. The temperature setting can be adjusted while the device is heating up to temperature. It is recommended to utilize the lower temperature settings when using the Dr Dabber Boost Evo, to maximize flavor, and the higher temperature setting are recommended to maximize vapor production.

• Temp 1 – 500 Degrees – Pink
• Temp 2 – 550 Degrees – Purple
• Temp 3 – 600 Degrees – Blue
• Temp 4 – 650 Degrees – Green
• Temp 5 – 700 Degrees – Orange
• Temp 6 – 750 Degrees – White

How Do I Use My Dr Dabber Boost Evo?

• After powering the unit on and adjusting the temperature setting to your preferred temperature, remove the glass attachment from the unit and add water. The attachment should be filled with water from the top and the water level should be a couple of millimeters above the percolator holes in the glass attachment.
• Attach the water bubbler attachment to the quick connect adapter.
• Load the atomizer with your preferred materials.
• Place the quick connect adapter with the glass attachment attached back onto the Dr Dabber Boost Base.
• Press and hold the power button for thee seconds (3) to initiate heat up.
• Press and hold the airflow release button when ready to clear the glass attachment.

What is “Party Mode” on the Dr Dabber Boost Evo?

Party Mode is something we usually call “session mode”, after initiating heat up the Dr Dabber Boost Evo will hold the atomizer temperature for a certain number of seconds. You can adjust the party mode settings by completing the following steps:

• Power the unit off.
• While the unit is turned off, press and hold the power button to change the session mode time.
• The LED light will blink two times (2) to indicate a hold time of 20 seconds, or four times (4) to indicate a hold time of 40 seconds.

What is “Glow Mode” on the Dr Dabber Boost Evo?

Glow Mode is the when the LED lights are illuminated in a decorative pattern.

• To turn Glow Mode off or on, press the power button four times (4).
• Press the power button two times (2) to cycle between the five LED light presets on the Dr Dabber Boost.

What is “Stealth Mode” on the Dr Dabber Boost Evo?

Stealth Mode is when the LED lights on the Dr Dabber Boost Evo are dimmed.

• Press the power button two times (2) whole Glow Mode is off to turn Stealth Mode on or off.

Charging the Dr Dabber Boost Evo

The charger LED lights will indicate the batteries status, the charging LED’s will pulse white while the device and charging, then turn solid white when the device is fully charged.

When the Dr Dabber Boost Evo blinks its temperature setting color three times (3), this indicates low battery. Please charge the device with its included charger until the LED lights are a solid white, before use.

How Do I Clean My Dr Dabber Boost Evo?

• Remove the quick connect adapter and the glass attachment from the base.
• Remove the glass attachment from the adapter and clean the adapter with a cotton swab dipped in isopropyl alcohol. Be sure to avoid the colored portion of the adapter and clean only the metal ring at the bottom and the threading.
• You can also remove the silicone ring out of the top of the adapter and run it under hot water to remove any excess residue, use a cotton swab for more stubborn residue.
• Pour out the water from the glass attachment and pour in some warm water, you can give the glass attachment a good shake after the warm water is placed inside to loosen up residue.
• For more stubborn residue, you can pour in some isopropyl alcohol and salt into the glass attachment, give it a shake, followed by a rinse with warm water. Allow the glass attachment to fully dry before reassembling.
• Remove the atomizer from the base, the atomizer is connected to the base by a magnetic connection. Simply pull the atomize up to remove.
• With a cotton swab soaked in isopropyl alcohol, clean the inside of the atomizer. You can use a cotton swab soaked in hot water to remove any access residue. Let dry before assembling.

You should clean out the inside portion of the atomizer with a cotton swab and iso alcohol after each session to avoid a large amount of build up.

How Do I Recalibrate My Dr Dabber Boost Evo for My New Atomizer?

When purchasing a new atomizer, your unit must be recalibrated with the new atomizer to get the most accurate temperature readings.

• Turn the Dr Dabber Boost Evo off and be sure not to charge it within 15 minutes prior to recalibrating.
• While the unit is off, press the power button four times (4) and hold the power button on the fourth press to recalibrate the unit.
• A successful recalibration is indicated by the LED lights blinking white, if the lights are blinking red that means the calibration was unsuccessful.

If you are experiencing any issues with this device or have any additional questions, please send an email to info@e-nail.com, stating the specific problem. Please include a picture or video showing the fault and also include your order number.