sincerelysupermom
>
VLab

VLab Halo Atomizer (V1 Version)

SKU:
E-HALO-VLAB-V1-ATM
Condition:
New
Minimum Purchase:
1 unit
  •  VLab Halo Atomizer (V1 Version)
  •  VLab Halo Atomizer (V1 Version)
  •  VLab Halo Atomizer (V1 Version)
  •  VLab Halo Atomizer (V1 Version)
MSRP: $29.99
Sale Price $27.99
— You save $2.00

Coming Soon!

Description

Halo E-Rig Replacement Atomizer V1 Version

The VLab Halo Atomizer is designed for optimal heat performance. It's made without the use of any glues, plastics or fibers, creating the purest consumption experience ever. The Halo Atomizer has a NiChrome Coil, NiChrome is composed of Nickel and Chromium. The reason why this metal is used in coils is because of its high melting point, which means that this metal is unlikely to melt when exposed to high heat. NiChrome also has a low conductivity rate so when you are switching to a higher temperature settings it'll raise the temperature slowly, giving you super flavorful hits!

NOTE: There is no quartz bowl inside the atomizer if you buy the atomizer separately.

 

Whats the difference between the V1 and V2?

To tell the difference between these atomizers the V1 only has 3 Power Settings, whereas the V2 has 4 Power Settings. Also the V2 is slightly taller than the original V1 Atomizer.

 

The standard HALO kit includes a quartz bowl and a ceramic bowl.  

Quick Tips:


- Avoid disassembling your atomizer, clean fully assembled in 99% isopropyl alcohol.
- Avoid overloading, this will flood your atomizer and break it.

VLAB HALO FAQ

Why is My Halo Electric Dab Rig Blinking Three Times?

This indicates that there is a connection issue, please try the following steps:

  • Please unscrew the atomizer and make sure it is screwed in correctly, sometimes the atomizer will not make a clear connection with the firing pin on the base if the threading is off when the atomizer is screwed in.
  • If the Halo continues to blink three times, this may be due to a firing pin issue. There is a firing pin on the base and there is also a firing pin at the bottom of the atomizer.
    • There is a firing pin on the base and there is also a firing pin at the bottom of the atomizer.
    • Unscrew the atomizer, using a dab tool gently lift the firing pin slightly.
    • DO NOT lift the firing pin all the way out, this will cause the wiring to disconnect, and the atomizer will stop working completely.
    • Very slight lifting of the firing pin will help the atomizer to make a connection with the base and your Halo should start working properly again from there.
  • If neither of the above steps resolve the issue, we suggest replacing the atomizer.

Why is My Halo Electric Dab Rig Blinking Five Times?

This indicates that there is a short circuit, or low battery.

  • If the Halo base has come into contact with water, allow for the base to dry out completely and then try turning the device on again.
  • If the device is dead, please place the device on the charger and allow the Halo to fully charge before attempting to use it again.

How Do I Clean the Halo Atomizer?

  • Unscrew the atomizer from the Halo base by turning it counterclockwise.
  • Remove the quartz bucket insert from the atomizer.
  • Soak all parts in isopropyl alcohol for one hour.

—If the quartz bucket insert is stuck inside the atomizer do not attempt to pull it out, soak it in isopropyl alcohol to loosen up the built-up residue and then attempt to remove it from the atomizer.

Warning:

      • Make sure the atomizer is fully cool to the touch before unscrewing it.
      • Be sure the device is powered off before cleaning.
      • After cleaning allow for all parts to dry completely before reassembling.
      • Do not blow into glass attachment while it is filled with water and is attached to the base.
      • Do not overfill the glass attachment with water.
      • Wait at least one minute between heating cycles.
      • Do not store this device while the glass attachment is filled with water.
      • Keep away from high humidity and moisture, it is best to store the Halo E-Rig in a dry dark place when not in use.
      • Do not overfill the atomizer, this will cause the atomizer to flood resulting in the need of a new atomizer.

If your device is still not working correctly, please send an email to info@e-nail.com, stating the specific problem. Please include a picture or video showing the fault and also include your order number.

 

View AllClose
UNDER NO CIRCUMSTANCE SHALL WE HAVE ANY LIABILITY TO YOU FOR ANY LOSS OR DAMAGE OF ANY KIND INCURRED AS A RESULT OF THE USE OF THE SITE OR PRODUCTS OR RELIANCE ON ANY INFORMATION PROVIDED ON THE SITE. YOUR USE OF THE SITE AND YOUR RELIANCE ON ANY INFORMATION ON THE SITE AND USE OF PRODUCTS IS SOLELY AT YOUR OWN RISK.