Pulsar RoK Rainbow: Electric Dab Rig - Limited Edition Full Spectrum

How To Use Pulsar Rok

• 1. Make sure your device is 100% charged before use, it’ll take approximately 2 hours for a complete charge. The RoK’s lights will pulse red when charging and illuminate green when the device is fully charged. Do not overcharge the battery, the Rok displays the battery life when turned on.
• Three Green Flashes = Full Charge
• Three Yellow Flashes = Medium Charge
• Three Red Flashes = Low Battery
• 2. Add water to the bottom glass beaker base on the Rok, it is recommended to fill the beaker halfway. You can remove some water based on preference, but do not fill it past the halfway point.
• 3. Attach the RoK disc perc downstem to the opening found between the two metal air path tubes. Insert with a slight twist motion and secure the perc flush inside the silicone housing. Do not use excessive force when affixing the perc to the unit.
• 4. Set the RoK beaker base filled with water onto a level surface. Gently place the RoK body onto the beaker base aligning the lip on the beaker base with the silicone track found at the bottom of the RoK body.
• 5. Once aligned, gently press down at a slight angle, simultaneously applying a rolling pressure to the RoK body so that the lip and track attach and lock into place. The fit should be snug and secure. Do not force or place high pressure onto the beaker base on this step.
• 6. Turn the device on by clicking the power button 5 times fast.
• 7. Toggle through the temperature settings by clicking the power button 3 times fast.
• Green Light – 680 Degrees
• Blue Light – 780 Degrees
• Red Light – 850 Degrees
• 8. Now that the temperature setting is selected, you can use a loading tool/ dab tool to place your desired amount of concentrates into the quartz bucket insert. Make sure to place the concentrates onto the bottom of the quartz bucket insert and not the side walls.
• 9. Press and hold the power button for 5-15 seconds to preheat the concentrates to your desired preference.
• 10. Place the carb cap on top of the atomizer.
• 11. Press and hold or “pulse” the power button to fire the RoK to your desired preference. The device will time out after the button is held for 30 seconds.

• For a more hands-free experience press the power button two times to activate session mode which will heat the device to the selected temperature and hold it for 30 seconds. To stop session mode after it’s been activated, simply click the button two times again.
• 12. There is a ceramic coil cup and a dry herb carb cap included in the RoK kit that is made to be used with dry materials. You can use this ceramic coil cup at the lowest heat setting to produce a dry herb vaporizer experience. The higher heat settings will produce more of a flower and waterpipe kind of experience.

How Do I Clean My Pulsar RoK Electric Dab Rig?

• For optimal use and flavor, use a cotton swab to clear out any left-over residue between sessions. After every few sessions it is recommended to clean the cups with cotton swabs soaked in isopropyl alcohol until clean to preserve the quality and lengthen the lifespan of your coil. Make sure the to wait until the coil has cooled down before cleaning. DO NOT submerge the entire atomizer in solution.
• To clean the glass components on the RoK start by removing the glass parts, clean with isopropyl alcohol and rinse with cold water. Be sure to allow all parts to dry completely before reassembling.
• To clean the metal pathways, remove the glass downstem and pull out both metal tubes out of the silicone housing and soak in isopropyl alcohol. Use a cleaning brush to remove and left-over residue after soaking. Once all residue is removed rinse with cold water and let air dry. To further clean the air path, disassemble the RoK collar and remove the coil, remove the mouthpiece and silicone splash protector. Dip a cleaning brush into alcohol solution and proceed to clean both air paths that hold the metal air path tubes. Rise the cleaning brush with water and repeat cleaning the airpaths.
• The clean the mouthpiece remove the metal mouthpiece and silicone splash guard insert, clean them both with mild soapy water and allow to air dry. Be sure to insert the silicone guard by following the track line within the RoK mouthpiece cavity.

• Periodically clean the connection to the atomizer on the base with a cotton swab dipped in alcohol, let dry before reattaching the atomizer.